If you can wait a couple weeks, AliExpress is going to be the cheapest.

eBay may be a bit more expensive, but it’s often my go-to because you can find everything and usually there are options with short shipping times.

For not too obscure parts, I would look at Reichelt, their prices are surprisingly low (especially if you bundle your orders to save on shipping costs).

HiPER Calc Pro. A great scientific calculator I use constantly. (There is also a unpaid, ad-supported version, and the ads weren’t too intrusive the last time I tried it)

That’s probably not a bad idea, although I doubt it will make much of a difference. But since you’re redesigning the whole thing, might as well do it.

It looks like you would want an even airflow through the whole PSU. The main heat-generating components are using the sides of the housing as a heat sink. I’m guessing the fan is mostly so the air inside the housing doesn’t get too warm, not to cool individual components.

Where is the original air exhaust? If it’s near the bottom of the picture, that would confirm my theory. In that case, I would keep the fan placement as close to original as possible (i.e. the blue square).

You can use a boost converter to boost the 5V of an USB port to the 19V your notebook needs.

Assuming 5A output from a powerbank (which is probably about the max you will get without USB PD), you could theoretically get 0.55A at 19V. With the unavoidable inefficiencies, you will get less.

So, maybe enough to very slowly charge your notebook while it’s off. But when it’s turned on, the battery charge will still drop.

Sure, the skull is biodegradable. But didn’t you know that large-scale human farming is responsible for the vast majority of CO2 emissions?!

Thanks for breaking it down for me! I think I’ll stick with the B650 motherboard for now.

Right, I guess I assumed CPU naming makes sense, so surely the lower number CPU must be worse in every way, right?😜

Looks like going with the 7700X is a no-brainer for me then.

As for your upgrade recommendations: Can you explain the benefits of a higher-end mainboard? I would think the mainboard shouldn’t make a huge difference, as long as it’s from a reputable manufacturer and compatible with all the other parts.

Thanks for your help!

Right, I might just see what cooler I can get second-hand. Thanks for your input!

This seems to be a bug in the slicer. I’m seeing the same issue in OrcaSlicer if the skirt height is set to more than one layer (even if the skirt is disabled). This makes sense if a skirt is used (can’t print a continuous spiral if you have to switch between printing the object and the skirt), but not if it’s disabled.

What slicer are you using? If it’s a PrusaSlicer fork, this is likely the same bug.

It looks to me like a JST SH connector: https://www.sparkfun.com/products/retired/10357

Measure the distance between the two pins - if it is 1 mm, this is most likely the connector you’re looking for.

From a cursory read of the datasheet, using the “dead time control” pin seems to be the way to go. Basically, this pin is used to set the voltage, while the error amplifier inputs (that’s the closest function to “over current protection” this chip has) are used to adjust the output according to the load. For your application, you probably don’t need to use them at all.

My instinct would be to disable the error amplifiers by connecting pins 1,2,15 and 16 to GND. You can then connect the wiper pin of the potentiometer to the deadtime control input, with the other pins of the potentiometer connected to GND and 3.3 V.

I haven’t worked with this chip before, so take this with a grain of salt. You should probably use a simulation tool to check the circuit before you start destroying chips.

Do you expect every meme to be meticulously handcrafted? It’s a stupid joke, not a work of art.

Close, but the word ends in -le, not -ie. The -le suffix is used as a diminutive form in some German dialects.

A small pair of vernier calipers. I don’t use them a lot, but sometimes they come in very handy.

What did you expect? We’re talking about one guy who might have lived over 2000 years ago. You’re not going to find his birth certificate and social security number.

The best anyone can do is assign a probability to his existence. And reading the article you yourself linked to, that probability seems to be pretty high.

Sorry dass ich nichts hilfreicherws beizutragen habe, aber der Janosch passt hier einfach zu gut:

Herr Janosch, schwere Entscheidungen, wie trifft man die? “Man schreibt die Alternativen tabellarisch auf einen Zettel. Anschließend legt man den Zettel nieder und wirft einen Löffel auf den Zettel. Dann geht man weg und lässt den Löffel das regeln. Sein Problem.”

It is more efficient to have a ship moving with cargo than without, but that doesn’t mean there aren’t additional emissions. The ratio of profit to effort is just higher because there is some profit as opposed to none. You wouldn’t load a ship up with useless mass you can’t sell just so you’re shipping something.

Your argument is like always running the heater in your car because that way the engine heat is at least used for something. Yes, technically the efficiency goes up because more of the energy in the fuel is harnessed. But that doesn’t mean the fuel usage or emissions are any lower, and in the summer the heater doesn’t do you any good either.

I have my pi-hole setup as the upstream DNS in my router, with cloudflare as a secondary DNS. That way, all my devices always use the router for DNS (since that’s what is advertised in my DHCP) and the router then uses pi-hole if it’s available, or cloudflare if it isn’t. But the individual device doesn’t get to choose between different servers.

That study states that brain damage can cause more conservative views, but the reverse isn’t true. Not everyone with conservative views has brain damage.